Search Results for ‘gauge’

Hey all, Any ideas if off-theshelf lcd gauge displays work on a 2012 TB48? Something like in the photo, for live data of temps, pressure, voltage, speed etc. Heard that the TB48 patrols 2017 and below don’t show readings. If anyone knows ones that are compatible with a 2012 model please let me...

I've always been a tinkerer and looking for a boost gauge solution and I heard of Arduino a while ago so I looked it up. Amazed how cheap this stuff is and info readily available for just about anything. I've been fine tuning a boost gauge and dual battery setup on a small 1.3oled which will fit...

Hi everybody. It seems my water temp gauge on my GU3 zd30 DI has died, I've been led to believe and what I can decipher from the service manuals is that the ZD30 has two! One which reports to the Computer, its a two pin connector, left of the alternator, screwed diagonally into the head...

Hey all. Just got around to fitting a a 3inch straight through exhaust on the old girl, while i was doing so i had the turbo off so decided it would be a good time to add some extra guages. The EGT probe is Pre turbo, I have only done a small couple of trips since, getting readings up to 550c...

Hi All! First post, I have done a lot of research around this but haven't found much.. Im having some overheating issues with my Patrol Ute, going up a hill in 3rd foot slowly making it the temp gauge creeps up to 3 quarters, once at the top of the hill if I back off the temp gauge goes...

Hi guys, I finally got round to installing my Autron gauges today, the dual batter gauge works fine but the EGT/BOOST is causing me some problems. The boost side is working but the EGT doesn't register on the gauge at all. The temp sensor is screwed into the bung that i had welded onto the...

Hi Guys, Been looking at some gauges and just wanting some opinions on them. I have been looking at autometer boost, EGT and temp, but have found autotron gauge that does it all are they any good? Quality...

Sorry if this in the wrong area, I couldn't decide if to go electrical or not. I have installed Autometer Cobalt series EGT and Boost but the back lighting on the gauges is different levels. Are these likely to have different LED's inside them? Is there some way to get the set the same? It...

i was just wondering if anyone knows if its possible to have your boost readout on your carputer on a td42.

Hi evryone. Where can I fit an engine temperature sender into a 3Ltr GU3 Y61? I am looking at fitting an after market Temp Gauge to monitor exact engine temperature instead of just hot warm cold as per the original in the dash. I want to keep the originals though. so dont want to get rid of the...

Hi guys Just wondering if anyone has put an electric water temp gauge in their Patrol? I have an 09 however finding it difficult to get anyone to install it. I have spoken to an auto electrican who said you need an adapter (so as to keep the original sender working) however I would like to...

Help! I have a Y61 TB45E Patrol SGL-E (Saudi arabia) and the Temp guage is at its normal (around 80degrees c) below the C. (before changing the MAF it was on the C. Surely normal at 80 would be in the middle between the Hand the C ...kinda in the middle.??? see the pic. How do I adjust the...

Did a search couldnt find what i was after. About to fit 3 52mm gauges to my GQ 4.2 (EGT, Fuel Gauge and Prob boost) and was wondering where everyone fits them? Have You put them in/on the dash? Made or bought a housing or fitted them to the pillar etc. any1 used the gauges holders on...

Hi All, I have recently bought a aftermarket tacho for my RB30 and have wired it up so it works when you turn ignition on etc but cannot get it to work with my revs. The unit comes with a plug which only has one sender wire going into it. I assume this is meant to go to your negative side on...

Hello, I am wanting to put an after market oil pressure guage on my 2.8TD Patrol (RD28T) as a new sender from Nissan is £112 bit to steep for me. I also need to get an adaptor for my oil pressure tester gauge. Does anyone know the thread size for the sender unit? As far as I can work out it is...

Just finished installing a Boost gauge and Volt gauge into the dash of my GU. Going to put a switch on the Volt gauge so that i can see voltages of both batteries. **************************************************************************